Fluke Networks IntelliTone Pro 200 LAN Toner and Probe Kit brand new

Fluke Networks IntelliTone Pro 200 LAN Toner and Probe Kit brand new
Fluke Networks IntelliTone Pro 200 LAN Toner and Probe Kit brand new
Fluke Networks IntelliTone Pro 200 LAN Toner and Probe Kit brand new
Fluke Networks IntelliTone Pro 200 LAN Toner and Probe Kit brand new

Fluke Networks IntelliTone Pro 200 LAN Toner and Probe Kit brand new

Brand new sealed in plastic. Fluke Networks IntelliTone Pro 200 LAN Toner and Probe Kit. Digital Toner and Probe traces and locates cables on active network.

IntelliTone Pro 200 LAN Toner and Probe Kit Includes: IntelliTone 200 LAN Toner and 200 Probe, coax F connector adapter, (2) RJ11 and (2) RJ 45 patch cables, test leads with alligator clips, lanyards, quick start guide, and (2) 9 volt batteries. Ends cable location confusion, decisively rejects noise and false signals.

Locates cables on active networks, even when terminated at a switch. Isolates cable and wiring within a bundle, despite cable bleed.

Confirms cable location, verifies continuity, and detects faults (opens, shorts, and reversed pairs) in one step. Isolates individual wire pairs precisely by changing tone when shorted. Effectively traces and locates voice, audio, and video cabling. Get advanced SuperVision for locating cables more effectively at patch panels, switches, termination blocks, or hidden within bundles. Our new IntelliTone Pro LAN Toner and Probe Kits find the cables others can't.

The IntelliToneT Pro LAN Toner and Probe Series from Fluke Networks is the first toner and probe to offer digital and analog signaling all in one tool. That means it's equipped with the most powerful cable location technologies for any work environment. Use digital mode to trace and locate data cabling safely and effectively on active networks. Use analog mode to isolate individual wire pairs, and trace voice, audio, and video cabling. The IntelliToneT Pro LAN Toner and Probe Series from Fluke Networks gives you superior vision for locating cables hidden in floors, ceilings, walls, and in bundles.

Its breakthrough digital technology makes it the first tool to tone and trace safely and effectively on active networks. Only IntelliToneT Pro LAN Toners and Probes offer the powerful combination of digital and analog technologies to resolve common infrastructure problems that arise during installing, maintaining, and changing of your network. Digital and analog toning in one tool. Today's media networks are more diverse than ever. Most buildings have a combination of telephone, twisted-pair data, coax, and security/alarm wiring.

And termination of this diverse set of cabling types requires tools optimized for different frequencies, connector types, and work environments. Until now, no single tool has combined the right technologies to operate across all copper media types, and in all environments.

IntelliTone Pro changes that by combining cutting-edge digital and analog signaling to locate and verify virtually any copper cable, regardless of application or environment. IntelliTone Pro's digital encoded signal should primarily be used on high-grade data cabling. / Cat 6a, and in active network environments. It operates at a high-frequency to match the higher frequency data the cable plant is designed to carry.

This allows the tone to overcome competing data signals and aggressive low-frequency terminations of. That means LAN cabling technicians can quickly zero in on the right cable during installations or troubleshooting. Digital toning is especially helpful once the cable has been located as it displays cable wiremap and checks for shorts, opens and miswires.

The IntelliTone Pro 200 probe has an. Input port and CableMap feature, allowing it to be plugged directly into a patch panel or wall port. The benefit of this wiremap test is two-fold. It eliminates the need for both a toner to a wiremapper, and provides 100% confirmation that the right cable has been located.

IntelliTone Pro's SmartTone analog toning can be used on voice-grade cabling (Cat 3 and below), as well as coax, security/alarm, and speaker wiring. These cables are optimized for lower frequency transmissions, and therefore are more easily isolated with a low-frequency tone. It should also be used in areas with relatively low interference from electronic devices.

In high-interference environments, digital may still be a better choice. SmartTone analog toning eliminates frustrating guesswork locating individual wire pairs during installations. The SmartTone analog signal will change'songs' each time the pair under test is shorted together. This provides telecom technicians a decisive way to identify individual wire pairs before punching them down on a jack or a block, or when diagnosing voice transmission problems. The IntelliToneT Pro LAN Toner uses the unique properties of. Cabling to create a balanced signal that minimizes the effect of signal bleed. The smart digital signal processing in the IntelliToneT Pro Probe clearly identifies this signal with audio and LED visual indicators, allowing you to rapidly isolate the correct cable from a bundle or on a patch panel. IntelliToneT eliminates hours of cable confusion -and you can count on getting it right the first time. With traditional analog toners and probes, isolating individual wire pairs precisely can be almost impossible because of signal bleed between pairs. As a result, wire pairs are often routed and terminated incorrectly the first time. IntelliTone Pro's SmartTone analog technology cuts out the guesswork and improves accuracy by providing definitive confirmation when the pair under test is located.

Just short the pair under test, and the audible tone will change its cadence. Eliminate callbacks during cabling moves, adds and changes with the powerful diagnostic capabilities of IntelliTone. The IntelliTone Pro 200 Probe features a CABLEMAP capability that identifies common cable miswires in twisted pair cabling.

IntelliTone technology automates the testing of each conductor for end-to-end continuity; LED lights and tones clearly indicate miswires such as opens, shorts or reversed pairs. Modern network devices use aggressive termination schemes for cables connected to their ports. While this termination reduces noise and. In the cable, it can also absorb an analog toner signal, making the connected cable impossible to detect with an analog audio probe. The result is that locating an unlabeled network can take hours with analog technology.

Unlike analog signals, the IntelliTone digital signal stays strong despite common mode termination. And the IntelliTone Pro Toner automates toning individual cable conductors, making it quick, efficient and safe to locate cables on active networks. Identify and diagnose POTS with multi-line Telco detect, polarity and ring indication.

IntelliTone Pro 200 Toners take the guesswork out of hunting for an active jack, or a jack with the right service. LEDs clearly identify common services found on today's networks, including telecom and datacom services and 10/100/1Gb Ethernet links.

Telecom Troubleshooting - Check telecom services with Line 1 continuity and polarity testing on the IntelliTone Pro 100 and 200 Toners. The IntelliTone Pro 200 Toner adds Line 2 troubleshooting. Confirm telecom circuits with the built-in talk battery capability.

Perform moves, adds and changes with powerful diagnostic capabilities of the IntelliTone Pro LAN 200 Toner & Probe. Toning - IntelliTone makes it easy to quickly locate the cable in the equipment closet when performing moves, adds and changes. Unconnected cable can be quickly isolated in the presence of bleed. Cablemap - The IntelliTone Pro 200 LAN Probe features a CABLEMAP capability that identifies common cable miswires in twisted pair cabling. Complete per-pin verification of TIA568 wiring identifies the exact wire that is open, shorted or miswired.

LED lights and distinctive tones clearly indicate miswires. The built-in Cablemap feature eliminates the need to carry separate tools or returning to the far-end to replace the toner with a mapper.

The IntelliTone Pro 200 Kit is the all-in-one tool to locate and map Category 5 cabling even when plugged into a switch, and verify link service after moves, adds and changes. Verify Ethernet Service - Is the link pulse correct, reversed due to a swap cable of uplink port, or MDIX capable?

Identify active Ethernet services present at the office wallplate. LED lights clearly indicate the presence of normal, reversed or MDIX Ethernet link connectivity. IntelliTone Pro is a digital toning system optimized for toning into modern network equipment and Category 5 cabling. To achieve this, IntelliTone uses radio frequencies and a digital tone packet that drives all 4 pairs with a variety of toning methods.

Datacom network moves, adds and changes using IntelliTone Pro Toners and Probes. In recent years, installation of structured cable has been to uniform standards.

The TIA-568A standard requires that all work areas be wired with a minimum of two jacks with the horizontal cabling being four-pair 100 ohm. This typically consists of 2 or more. Runs directly from a wall plate jack to a patch panel.

Plugging in IntelliTone is a digital toning system featuring an 8-position modular jack. This allows the toner to be plugged in either at the wall jack with the included.

Or, if the wall jack is obstructed but connected, the. Can be removed from the PC and plugged directly into the toner. Wall jacks are often unmarked or misconnected. Adding to the confusion, the 8-position modular jack can be used for either data or telecom services. Service ID provides the first clue The IntelliTone Pro 200 LAN Toner features a service ID indicating the presence of service on the line.

When plugged in to a wall jack, it provides the first indication of where to look for the cable in the closet. A 4-position jack is sure to be telecom service, whereas an 8-position jack could be telecom or data (network) connection. The presence of Ethernet indicates the connection is active and best located on the patch cables from the patch panel to the switch. If the connection is open then it likely not patched or connected.

If the open LED is extinguished, the toner is detecting a connection across the center pins of the jack. This could be an un-plugged network device or unrecognized service. Locating in the closet The tone can be located on un-patched connections by moving the probe from jack to jack on the patch panel.

It is typical to get a reading of 4-6 in locate mode with the black probe tip inserted into the jack. Neighboring jacks and cable will exhibit lower signal levels as indicated by the LED display. If the service identification in the office indicated an Ethernet connection, the user should begin probing the cables that are patched to active network equipment.

It is typical to get a reading of 7-8 on the toned cable. Once the cable is located, the IntelliTone Pro 200 LAN probe provides a Cablemap to assure correct pin-to-pin wiring.

By removing the patch cable from the switch, or by plugging a patch cable into the patch panel jack, the complete end-to-end wiring can be verified for opens, shorts, or mis-wires. When in tight spaces or in the presence of bleed, the isolate position will help eliminate bleed and provide more granularity on the stronger LEDs.

This will aid in differentiating the toned cable or jack from its neighbors by providing a couple of LED levels of difference in strength. Additionally Cablemap always provides a definitive indication of the toned cable. Toning from the closet to office jack Occasionally toning may be performed from the patch panel to the office jack. If the jacks are very closely spaced or it is difficult to insert the probe tip in the jack, there may only be one or two levels of signal strength difference. If more differentiation is required for extremely close jacks, a short patch cable can be used to effectively distance the jacks by probing the cable as it is moved from jack to jack. The same patch cable can then be used to validate the correct cable using the Cablemap feature on the IntelliTone Pro LAN 200 probe. Telecom moves, adds, changes using IntelliTone Most office installations consist of a one or more data and telephone drops.

On the telecom side, there can be a variety of jacks and wiring schemes ranging from a single pair on a 4-position wall jack to 4 pairs connected from the 8 position modular jack to the terminating block. Wiring Schemes In the office, the wall plate jack may be 6 or 8-postion, with the 6-position jack having 4 or 6 pins.

Horizontal cabling uses 1, 2, 3, or 4 pairs and can range from Category 3 to Category 5 cable. In the closet, the horizontal cabling will typically terminate on a 110 block, or in older sites a 66 block. The block may be directly connected to the PBX if this is the main distribution frame (MDF), or cross-connected to another location if this is an intermediate distribution frame (IDF). Current practice, per TIA-568A standard, consists of an 8-position jack in the office with 4-pair 100 ohm UTP connected to a 110 block. Plugging into a jack The IntelliTone toner features an 8-position modular jack that accepts 4, 6 or 8 position male plugs.

The included 4 and 8 position patch cables allow the toner to be plugged into the wall jack. Plugging in to a 66 or 110 block There are a variety of ways to connect the toner to the pair.

The supplied alligator test leads makes bare wire attachment possible. For piercing wires, Fluke Networks offers the MT-8203-20, a telecom 5-way Alligator Lead Set with a bed of nails. The telecom 5-way Alligator Lead Set also offers a secure attachment to 66 blocks using the U shaped nose for blade shaped terminals. It is also possible to use a 66 quick clip and connect to the toner using the 8-position modular plug. For 110 blocks, a standard 1-pair 110 to modular plug patch cable can be plugged directly into the toner modular jack. There are also various 110 test adapters that provide a modular jack for connection to the toner. Isolate Individual Wire Pairs The IntelliTone digital signal is subject to significant bleed-over between pairs in a cable. This is especially true for Cat 3 cabling. Because of this, IntelliTone's analog mode is recommended for isolating individual pairs. The SmartToneT analog mode should be used because of its ability to change cadence when the pair under test is shorted. When the pair under test is not terminated, the copper conductors can be touched together briefly to cause a short. When this happens, the tone will change its cadence to indicate that the correct pair has been located. If the pair is terminated on a 66 or 110 block, it may be necessary to short the pair together with a pair of insulated pliers. In the distribution frame In the closet, the telecom jack will typically terminate on a 110 block. The block may be directly connected to the PBX if this is the MDF, or cross-connected another location if this is an IDF.

More recent installations, per the TIA-568 standard, consist of an RJ-45 jack in the office with all 4 pairs punched down on the 110 block. Locate the cable by touching wire with the tip, either the insulation or by making metalic contact. Once located, the office wiring can be verified for shorts, opens and mis-wires using a standard 110 to 8-position patch cable and the Cablemap feature on the IntelliTone Pro LAN 200 probe.

The cables are readily available in 1, 2 and 4-pair 110 connection in TIA-568A, TIA-568B or Universal Service Ordering Code (USOC) formats. The Cablemap results will show the correct order when the patch cable matches the wiring scheme, be it TIA-568A, TIA-586B and USOC. The IntelliTone Pro LAN probe supports the time-honored practice of making contact with the finger.

While often done on 66 blocks, it is possible to make the contact with the 110 connections using a metallic object. Using the body to conduct the signal is a good way to move the probe away from noise sources and identify individual wires when metallic contact is possible. Locating Cables on an Active PBX System Some PBX lines generate signals in the operating frequency of IntelliTone as seen by the SYNC LED flashing red.

In this case, it may be difficult for IntelliTone to differentiate the PBX signal from the IntelliTone signal. Once again, it is recommended to use IntelliTone's analog mode for this application. Make sure that both the IntelliTone Pro Toner and the IntelliTone Pro Probe are in analog mode.

Moves, adds, changes completion When returning to the office to retrieve the toner, the presence of the correct services on the correct jacks can quickly be verified using the IntelliTone Pro 200 toner Service ID feature. This item is in the category "Business, Office & Industrial\Test, Measurement & Inspection\Other Test, Measurement & Inspection". The seller is "ingaldi_90" and is located in this country: GB. This item can be shipped to United Kingdom, Antigua and Barbuda, Austria, Belgium, Bulgaria, Croatia, Republic of, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Australia, United States, Bahrain, Canada, Japan, New Zealand, Israel, Hong Kong, Norway, Indonesia, Malaysia, Mexico, Singapore, Korea, South, Switzerland, Taiwan, Thailand, Bangladesh, Belize, Bermuda, Bolivia, Barbados, Brunei Darussalam, Cayman Islands, Dominica, Ecuador, Egypt, Guernsey, Gibraltar, Guadeloupe, Grenada, French Guiana, Iceland, Jersey, Jordan, Cambodia, Saint Kitts-Nevis, Saint Lucia, Liechtenstein, Sri Lanka, Macau, Monaco, Maldives, Montserrat, Martinique, Nicaragua, Oman, Pakistan, Peru, Paraguay, Reunion, Turks and Caicos Islands, Aruba, Saudi Arabia, South Africa, United Arab Emirates, Chile, Bahamas, Colombia, Costa Rica, Guatemala, Honduras, Jamaica, Kuwait, Panama, Philippines, Qatar, Trinidad and Tobago, Uruguay, Vietnam.


Fluke Networks IntelliTone Pro 200 LAN Toner and Probe Kit brand new